18. In this Chapter –
"span-restriction device" – a device on a stepladder that secures both legs of the ladder against sliding;
"climbing" – ascending or descending a ladder without performing additional work and without carrying loads in the hands;
"compensation mechanism" – a mechanism permanently installed at the base of the stiles of a ladder, enabling the extension of one stile for the purpose of positioning the ladder perpendicularly to ground or a floor that is not in the same plane as the ladder's stiles;
"extension ladder" – a ladder composed of two or three sections, with parallel stiles, which can be opened or closed according to the required working height;
"mobile ladder" – a ladder with wheels at its base enabling its mobility;
"leaning ladder" – a ladder without self-support, whether extension or non-extension;
"standing ladder" – an upright ladder with an upper standing platform whose minimum width and depth are 25 cm;
"stepladder" – a self-supporting ladder that can be climbed on one side or on both sides, as the case may be;
"fixed ladder" – a ladder anchored and secured to a permanent structure;
"ladder scaffold" – a scaffold whose floor rests on ladder rungs.
19. The provisions of this Chapter shall apply to all work at height performed by means of a ladder, including abseiling work and mast climbing, and to the ladders used for work at height.
20. A performer shall ensure that no use is made of a ladder that is not a fixed ladder unless one of the following conditions is met in respect of it:
(1)it meets the requirements of Israeli Standard SI 1847 and is suitable for the nature of the work being performed;
(2)it is a leaning ladder serving as a passageway between floors, forming part of a stanchion scaffold or an independent scaffold as defined in the Work Safety (Construction Works) Regulations, 5748-1988, provided that it meets the requirements of Israeli Standard SI 1139;
(3)it is a three-legged stepladder intended for performing agricultural work on trees, whose height does not exceed 3 metres, provided that it has a sound structure, is sufficiently reinforced, has no visible defect, and the distance between its rungs is not less than 25 cm and does not exceed 30 cm;
(4)it is a wooden ladder serving as a passageway between different levels in construction works, provided that the following requirements are met:
(a)if its length exceeds 2 metres, it shall be reinforced at least every 1.5 metres by means of tie bolts or by rear wooden reinforcements;
(b)its stile shall have a cross-sectional area of not less than 45 square centimetres and its width or diameter shall not be less than 4.5 centimetres; its fibres shall be as straight as possible and their direction shall be approximately parallel to the length of the stile;
(c)the rungs of the ladder shall be of adequate strength, set well within the stiles or supported by wooden brackets properly connected to the stiles from rung to rung;
(d)no rung shall be missing from the ladder and no rung shall be defective; the distance between rungs shall be uniform, not less than 25 centimetres and not exceeding 30 centimetres, and no rung of the ladder shall be connected to a stile other than by nails or by appropriate connecting means.
21. (a) A performer shall supply at the workplace ladders in accordance with the provisions of this Chapter, without defect, made of suitable material, of a type suited to the nature of the work being performed, in dimensions and heights appropriate to the place of their installation and in the quantity required.
(b)A performer is responsible for ensuring that after an uncontrolled fall of a ladder or after its transport by vehicle, the ladder is inspected to verify that its components have not been damaged and that no cracks, distortions or unreasonable gaps between its parts have been created.
(c)A performer shall disqualify defective ladders from use and shall take appropriate measures to prevent their use; the ladders shall be returned to use only after they have been repaired in accordance with the standard requirements; a ladder that cannot be repaired shall be destroyed in a manner that prevents further use of it.
22. (a) A performer shall ensure that a worker shall not climb a ladder longer than 2 metres except to within one metre below its upper end.
(b)Sub-regulation (a) shall not apply if at the highest point to which the worker will reach by use of the ladder there is a suitable handhold at a height of approximately one metre above the position where his feet stand, including where work is performed on a standing ladder with a handrail at a height of approximately one metre above the upper standing platform.
23. A performer shall ensure that a worker shall not work at height on a ladder unless all of the following conditions are met:
(1)he is secured in a functioning, complete safety harness fitted to his measurements;
(2)he is secured by a fall-arrest system appropriate to the nature of the work being performed;
(3)the fall-arrest system is anchored to a stable part;
(4)he is wearing a protective helmet and safety shoes with special anti-slip soles.
24. (a) The following operations may also be performed without complying with regulations 23(1) to (3) in these cases:
(1)climbing a non-fixed ladder whose height is up to 6 metres, for passage between different levels;
(2)climbing a ladder and performing work that is not prolonged or strenuous or that does not require tilting the person's body in a manner that will cause him to lose balance, on a ladder whose height is up to 4.5 metres.
(b)Regulation 5(1) shall not apply to harvesting work in agriculture on a ladder whose height is up to 3 metres, if the worker is a young person as defined in the Youth Labour Law, 5713-1953.
25. (a) The worker and the performer shall ensure that a leaning or stepladder is placed on a firm base, evenly on its stiles, by means of rubber pads, metal spurs or another appropriate stop at the base of the ladder, and that it is leaned against and rested on a stable support, so that no accidental movement from its position is possible during use, all in accordance with the circumstances and the type of surface and manner of positioning the ladder.
(b)In addition to what is stated in sub-regulation (a), if there is concern regarding the stability of the ladder or the ladder has been positioned at a distance of less than 30 cm from the free edge of a surface, a person shall stand by the base of the ladder and hold it to prevent it from being moved from its position.
(c)A mobile ladder shall be secured by a device for stopping the wheels to prevent undesired movement as long as a person is or may be on it.
(d)A leaning ladder shall not be positioned except when its lower resting point rests on two stable points on both stiles located at the same level, and its upper resting point rests on two stable points on both stiles located at the same level; if it is not possible to position the upper part of a ladder so as to enable it to rest on both stiles, including on a pole, mast, tree trunk or external corner of a structure, the ladder shall be equipped with a suitable fitting at its head that, by its strength and dimensions, will enable the work to be performed safely.
(e)No use shall be made of a ladder equipped with a compensation mechanism.
(f)A leaning ladder shall be placed at gradients of between 1 horizontal to 4 vertical and between 1 horizontal to 2 vertical (at an angle of between 65 and 76 degrees with respect to the horizontal), and appropriate measures shall be taken to prevent it from overturning or sliding during use.
(g)A stepladder shall be positioned so that its span-restriction device is fully open; no use shall be made of a stepladder whose span-restriction device is not functioning.
(h)When resting a ladder above an opening in a wall or structure, the head of the ladder shall be at a height of at least 30 cm above the opening.
(i)A ladder shall not be positioned facing a door that may open, unless safe means have been taken to prevent it from opening for as long as the ladder is positioned close to the door.
(j)A ladder shall not be positioned in a place serving as a passageway for persons or motorised vehicles, unless such positioning is essential, and in any event the duration of the positioning shall be as short as possible, and measures shall be taken to prevent the passage of persons or motorised vehicles at the place of positioning.
(k)No heavy load unsuited to the purpose of the ladder shall be raised on a ladder; only one person shall stand on a rung of a ladder; the load on the ladder shall not exceed 150 kg.
(l)A worker standing on a ladder shall not pass to another elevated platform unless the platform is stable, adjacent to the ladder and properly fixed.
26. A performer shall ensure that –
(1)climbing on a ladder shall be done so that the worker faces the ladder and both hands are free of any object in order to hold the ladder;
(2)climbing on a ladder shall be done in a manner enabling the worker to hold on to at least three support points at each stage of climbing; it is permissible to make do with support points for the feet for the purpose of performing work where one of the following conditions is met:
(a)the worker is equipped with a safety harness and is connected to a positioning and work-support system that provides him with a safe and adequate hold at his back;
(b)the worker is standing on the standing platform of a standing ladder equipped with a guardrail comprising a top rail, mid rail and toe board on three of its sides, except on the side of ascent; the side of ascent shall be capable of being locked during work by means of a chain or other similar device at a height of 1 metre above the standing platform;
(3)no materials or objects likely to cause the worker to lose his balance during ascent or descent shall be placed near the base or the head of the ladder;
(4)no ladder shall be positioned on a surface whose area, structure or shape does not permit safe ascent, descent or access to it;
(5)a worker shall not climb a ladder from its inner side and in the direction opposite to the manner in which it was positioned;
(6)in a ladder serving as a means of connection between two storeys, two levels or two tiers of work platforms, the opening between the storeys through which the ladder passes shall be as small as possible without endangering the climber, and shall be enclosed on three sides, or alternatively the passage opening shall be equipped with a cover that shall be closed after each passage through it;
(7)no use shall be made of a non-fixed ladder as a means of connection between more than 2 storeys, 2 levels or 2 tiers of work platforms;
(8)electrical work, including work in the vicinity of electric lines under voltage as referred to in regulation 16, shall be performed only from a ladder whose stiles are made entirely of insulating material, and such work shall not be performed from a metal ladder or from a ladder made of insulating material whose stiles are equipped with metal reinforcing strips or steel cables;
(9)no work shall be performed without use of a fall-arrest system anchored to a structure above a stepladder whose height exceeds two metres, where the worker is in a straddling position above the head of the ladder.
27. (a) An occupier of a factory –
(1)shall ensure that a fixed ladder, its parts and connections, shall be of adequate strength and suitable for its purpose, and shall be fixed to the structure in a stable manner to prevent its collapse or detachment from the structure to which it is connected; the structure of the ladder, its parts, connections and manner of fixing to the structure shall be approved by a registered and licensed civil engineer;
(2)shall take appropriate measures to ensure that access to a fixed ladder is available only to those authorised to do so;
(3)where a fixed ladder equipped with a safety cage is present, shall install the cage at a height 2 of between 2.1 metres and 2.4 metres from the floor or rest platform, as the case may be, of sufficient strength and suitable for its purpose;
(4)where a fixed ladder without a safety cage whose height is above 6 metres, or a fixed ladder equipped with a safety cage whose height is above 10 metres, is present, shall equip it with a rigid vertical anchor line.
(b)A performer shall ensure that climbing and performing work at height above a fixed ladder shall be done by a worker equipped with a safety harness integrated with a positioning and work-support system, in addition to the fall-arrest system, except in the following cases:
(1)climbing a fixed ladder without a safety cage whose height is up to 6 metres, for passage between different levels, or climbing a ladder equipped with a safety cage whose height is up to 10 metres;
(2)climbing and performing work that is not prolonged or strenuous or that does not require tilting the person's body in a manner that will cause him to lose balance, on a fixed ladder whose height is up to 4.5 metres;
(3)permanent, stable rest platforms enclosed on three sides, adjacent to the ladder, are available, with the distance between them not exceeding 6 metres, provided that the requirement of sub-regulation (c) is met;
(4)the ladder is equipped with a safety cage along its entire height, with permanent, stable rest platforms enclosed on three sides, the distance between which does not exceed 10 metres, provided that the requirement of sub-regulation (c) is met.
(c)The passage openings and rest platforms referred to in sub-regulation (b)(3) and (4) shall be equipped with covers that shall be closed after each passage through them, or the sections of ladder adjacent above or below each passage opening or rest platform shall not be in a single vertical sequence.
28. A performer shall ensure that no use is made of a ladder scaffold.